stm32mp1xx_hal_conf.h

/**
 ******************************************************************************
 * @file    stm32mp1xx_hal_conf.h
 * @author  MCD Application Team
 * @brief   HAL configuration file.
 ******************************************************************************
 * @attention
 *
 * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
 * All rights reserved.</center></h2>
 *
 * This software component is licensed by ST under BSD 3-Clause license,
 * the "License"; You may not use this file except in compliance with the
 * License. You may obtain a copy of the License at:
 *                        opensource.org/licenses/BSD-3-Clause
 *
 ******************************************************************************
 */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32MP1xx_HAL_CONF_H
#define STM32MP1xx_HAL_CONF_H

#ifdef __cplusplus
extern "C" {
#endif

/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/

/* ########################## Module Selection ############################## */
/**
 * @brief This is the list of modules to be used in the HAL driver
 */
#define HAL_MODULE_ENABLED
//#define HAL_ADC_MODULE_ENABLED
//#define HAL_CEC_MODULE_ENABLED
//#define HAL_CORTEX_MODULE_ENABLED
//#define HAL_CRC_MODULE_ENABLED
//#define HAL_CRYP_MODULE_ENABLED
//#define HAL_DAC_MODULE_ENABLED
//#define HAL_DCMI_MODULE_ENABLED
//#define HAL_DFSDM_MODULE_ENABLED
#define HAL_DMA_MODULE_ENABLED
//#define HAL_EXTI_MODULE_ENABLED
//#define HAL_FDCAN_MODULE_ENABLED
#define HAL_GPIO_MODULE_ENABLED
//#define HAL_HASH_MODULE_ENABLED
//#define HAL_HSEM_MODULE_ENABLED
//#define HAL_I2C_MODULE_ENABLED
//#define HAL_IPCC_MODULE_ENABLED
//#define HAL_LPTIM_MODULE_ENABLED
//#define HAL_LTDC_MODULE_ENABLED
//#define HAL_MDMA_MODULE_ENABLED
//#define HAL_PWR_MODULE_ENABLED
//#define HAL_QSPI_MODULE_ENABLED
#define HAL_RCC_MODULE_ENABLED
//#define HAL_RNG_MODULE_ENABLED
//#define HAL_RTC_MODULE_ENABLED
//#define HAL_SAI_MODULE_ENABLED
//#define HAL_SD_MODULE_ENABLED
//#define HAL_SMARTCARD_MODULE_ENABLED
//#define HAL_SMBUS_MODULE_ENABLED
//#define HAL_SPDIFRX_MODULE_ENABLED
//#define HAL_SPI_MODULE_ENABLED
//#define HAL_SRAM_MODULE_ENABLED
//#define HAL_TIM_MODULE_ENABLED
#define HAL_UART_MODULE_ENABLED
//#define HAL_USART_MODULE_ENABLED
//#define HAL_WWDG_MODULE_ENABLED

// Modules ported from H7:
#define HAL_PCD_MODULE_ENABLED

/* ########################## Register Callbacks selection ############################## */
/**
 * @brief This is the list of modules where register callback can be used
 */
//#define USE_HAL_ADC_REGISTER_CALLBACKS    0u
//#define USE_HAL_CEC_REGISTER_CALLBACKS    0u
//#define USE_HAL_DAC_REGISTER_CALLBACKS    0u
//#define USE_HAL_I2C_REGISTER_CALLBACKS    0u
//#define USE_HAL_LTDC_REGISTER_CALLBACKS	0u
//#define USE_HAL_RNG_REGISTER_CALLBACKS    0u
//#define USE_HAL_SPI_REGISTER_CALLBACKS    0u
//#define USE_HAL_SRAM_REGISTER_CALLBACKS   0U
//#define USE_HAL_UART_REGISTER_CALLBACKS   0u
//#define USE_HAL_USART_REGISTER_CALLBACKS  0u
//#define USE_HAL_WWDG_REGISTER_CALLBACKS   0u

/* ################## SPI peripheral configuration ########################## */

/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
 * Activated: CRC code is present inside driver
 * Deactivated: CRC code cleaned from driver
 */
//#define USE_SPI_CRC                     1U

/* ######################### Oscillator Values adaptation ################### */
/**
 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
 *        This value is used by the RCC HAL module to compute the system frequency
 *        (when HSE is used as system clock source, directly or through the PLL).
 */
#if !defined(HSE_VALUE)
#define HSE_VALUE 24000000U /*!< Value of the External oscillator in Hz */
#endif						/* HSE_VALUE */

/**
 * @brief In the following line adjust the External High Speed oscillator (HSE) Startup
 *        Timeout value
 */
#if !defined(HSE_STARTUP_TIMEOUT)
#define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */
#endif							 /* HSE_STARTUP_TIMEOUT */

/**
 * @brief Internal High Speed oscillator (HSI) value.
 *        This value is used by the RCC HAL module to compute the system frequency
 *        (when HSI is used as system clock source, directly or through the PLL).
 */
#if !defined(HSI_VALUE)
#define HSI_VALUE 64000000U /*!< Value of the Internal oscillator in Hz*/
#endif						/* HSI_VALUE */

/**
 * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup
 *        Timeout value
 */
#if !defined(HSI_STARTUP_TIMEOUT)
#define HSI_STARTUP_TIMEOUT 5000U /*!< Time out for HSI start up */
#endif							  /* HSI_STARTUP_TIMEOUT */

/**
 * @brief Internal Low Speed oscillator (LSI) value.
 */
#if !defined(LSI_VALUE)
#define LSI_VALUE 32000U
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz                                           \
						   The real value may vary depending on the variations                                         \
						   in voltage and temperature.  */
/**
 * @brief External Low Speed oscillator (LSE) value.
 */
#if !defined(LSE_VALUE)
#define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */
#endif					 /* LSE_VALUE */

/**
 * @brief Time out for LSE start up value in ms.
 */
#if !defined(LSE_STARTUP_TIMEOUT)
#define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */
#endif							  /* LSE_STARTUP_TIMEOUT */

/**
 * @brief Internal  oscillator (CSI) default value.
 *        This value is the default CSI value after Reset.
 */
#if !defined(CSI_VALUE)
#define CSI_VALUE 4000000U /*!< Value of the Internal oscillator in Hz*/
#endif					   /* CSI_VALUE */

/**
 * @brief External clock source for I2S peripheral
 *        This value is used by the I2S HAL module to compute the I2S clock source
 *        frequency, this source is inserted directly through I2S_CKIN pad.
 */
#if !defined(EXTERNAL_CLOCK_VALUE)
#define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External clock in Hz*/
#endif								   /* EXTERNAL_CLOCK_VALUE */

/* Tip: To avoid modifying this file each time you need to use different HSE,
   ===  you can define the HSE value in your toolchain compiler preprocessor. */

/* ########################### System Configuration ######################### */
/**
 * @brief This is the HAL system configuration section
 */
#define VDD_VALUE 3300U								  /*!< Value of VDD in mv */
#define TICK_INT_PRIORITY ((uint32_t)(1U << 4U) - 1U) /*!< tick interrupt priority (lowest by default)             */
													  /*  Warning: Must be set to higher priority for HAL_Delay()  */
													  /*  and HAL_GetTick() usage under interrupt context          */
#define USE_RTOS 0U
#define PREFETCH_ENABLE 0U
#define INSTRUCTION_CACHE_ENABLE 0U
#define DATA_CACHE_ENABLE 0U

/* ########################## Assert Selection ############################## */
/**
 * @brief Uncomment the line below to expanse the "assert_param" macro in the
 *        HAL drivers code
 */
/*#define USE_FULL_ASSERT    1*/

/* Includes ------------------------------------------------------------------*/
/**
 * @brief Include module's header file
 */

#ifdef HAL_RCC_MODULE_ENABLED
#include "stm32mp1xx_hal_rcc.h"
#endif /* HAL_RCC_MODULE_ENABLED */

#ifdef HAL_EXTI_MODULE_ENABLED
#include "stm32mp1xx_hal_exti.h"
#endif /* HAL_EXTI_MODULE_ENABLED */

#ifdef HAL_GPIO_MODULE_ENABLED
#include "stm32mp1xx_hal_gpio.h"
#endif /* HAL_GPIO_MODULE_ENABLED */

#ifdef HAL_HSEM_MODULE_ENABLED
#include "stm32mp1xx_hal_hsem.h"
#endif /* HAL_HSEM_MODULE_ENABLED */

#ifdef HAL_DMA_MODULE_ENABLED
#include "stm32mp1xx_hal_dma.h"
#endif /* HAL_DMA_MODULE_ENABLED */

#ifdef HAL_MDMA_MODULE_ENABLED
#include "stm32mp1xx_hal_mdma.h"
#endif /* HAL_MDMA_MODULE_ENABLED */

#ifdef HAL_CORTEX_MODULE_ENABLED
#include "stm32mp1xx_hal_cortex.h"
#endif /* HAL_CORTEX_MODULE_ENABLED */

#ifdef HAL_ADC_MODULE_ENABLED
#include "stm32mp1xx_hal_adc.h"
#endif /* HAL_ADC_MODULE_ENABLED */

#ifdef HAL_CEC_MODULE_ENABLED
#include "stm32mp1xx_hal_cec.h"
#endif /* HAL_CEC_MODULE_ENABLED */

#ifdef HAL_CRC_MODULE_ENABLED
#include "stm32mp1xx_hal_crc.h"
#endif /* HAL_CRC_MODULE_ENABLED */

#ifdef HAL_CRYP_MODULE_ENABLED
#include "stm32mp1xx_hal_cryp.h"
#endif /* HAL_CRYP_MODULE_ENABLED */

#ifdef HAL_DAC_MODULE_ENABLED
#include "stm32mp1xx_hal_dac.h"
#endif /* HAL_DAC_MODULE_ENABLED */

#ifdef HAL_DCMI_MODULE_ENABLED
#include "stm32mp1xx_hal_dcmi.h"
#endif /* HAL_DCMI_MODULE_ENABLED */

#ifdef HAL_DFSDM_MODULE_ENABLED
#include "stm32mp1xx_hal_dfsdm.h"
#endif /* HAL_DFSDM_MODULE_ENABLED */

#ifdef HAL_FDCAN_MODULE_ENABLED
#include "stm32mp1xx_hal_fdcan.h"
#endif /* HAL_FDCAN_MODULE_ENABLED */

#ifdef HAL_HASH_MODULE_ENABLED
#include "stm32mp1xx_hal_hash.h"
#endif /* HAL_HASH_MODULE_ENABLED */

#ifdef HAL_I2C_MODULE_ENABLED
#include "stm32mp1xx_hal_i2c.h"
#endif /* HAL_I2C_MODULE_ENABLED */

#ifdef HAL_IPCC_MODULE_ENABLED
#include "stm32mp1xx_hal_ipcc.h"
#endif /* HAL_IPCC_MODULE_ENABLED */

#ifdef HAL_LPTIM_MODULE_ENABLED
#include "stm32mp1xx_hal_lptim.h"
#endif /* HAL_LPTIM_MODULE_ENABLED */

#ifdef HAL_LTDC_MODULE_ENABLED
#include "stm32mp1xx_hal_ltdc.h"
#endif /* HAL_LTDC_MODULE_ENABLED */

#ifdef HAL_PWR_MODULE_ENABLED
#include "stm32mp1xx_hal_pwr.h"
#endif /* HAL_PWR_MODULE_ENABLED */

#ifdef HAL_QSPI_MODULE_ENABLED
#include "stm32mp1xx_hal_qspi.h"
#endif /* HAL_QSPI_MODULE_ENABLED */

#ifdef HAL_RNG_MODULE_ENABLED
#include "stm32mp1xx_hal_rng.h"
#endif /* HAL_RNG_MODULE_ENABLED */

#ifdef HAL_RTC_MODULE_ENABLED
#include "stm32mp1xx_hal_rtc.h"
#endif /* HAL_RTC_MODULE_ENABLED */

#ifdef HAL_SAI_MODULE_ENABLED
#include "stm32mp1xx_hal_sai.h"
#endif /* HAL_SAI_MODULE_ENABLED */

#ifdef HAL_SD_MODULE_ENABLED
#include "stm32mp1xx_hal_sd.h"
#endif /* HAL_SD_MODULE_ENABLED */

#ifdef HAL_SMARTCARD_MODULE_ENABLED
#include "stm32mp1xx_hal_smartcard.h"
#endif /* HAL_SMARTCARD_MODULE_ENABLED */

#ifdef HAL_SMBUS_MODULE_ENABLED
#include "stm32mp1xx_hal_smbus.h"
#endif /* HAL_SMBUS_MODULE_ENABLED */

#ifdef HAL_SPDIFRX_MODULE_ENABLED
#include "stm32mp1xx_hal_spdifrx.h"
#endif /* HAL_SPDIFRX_MODULE_ENABLED */

#ifdef HAL_SPI_MODULE_ENABLED
#include "stm32mp1xx_hal_spi.h"
#endif /* HAL_SPI_MODULE_ENABLED */

#ifdef HAL_SRAM_MODULE_ENABLED
#include "stm32mp1xx_hal_sram.h"
#endif /* HAL_SRAM_MODULE_ENABLED */

#ifdef HAL_TIM_MODULE_ENABLED
#include "stm32mp1xx_hal_tim.h"
#endif /* HAL_TIM_MODULE_ENABLED */

#ifdef HAL_UART_MODULE_ENABLED
#include "stm32mp1xx_hal_uart.h"
#endif /* HAL_UART_MODULE_ENABLED */

#ifdef HAL_USART_MODULE_ENABLED
#include "stm32mp1xx_hal_usart.h"
#endif /* HAL_USART_MODULE_ENABLED */

#ifdef HAL_WWDG_MODULE_ENABLED
#include "stm32mp1xx_hal_wwdg.h"
#endif /* HAL_WWDG_MODULE_ENABLED */

#ifdef HAL_PCD_MODULE_ENABLED
#include "stm32mp1xx_hal_pcd.h"
#include "stm32mp1xx_hal_pcd_ex.h"
#endif /* HAL_PCD_MODULE_ENABLED */

/* Exported macro ------------------------------------------------------------*/
#ifdef USE_FULL_ASSERT
/**
 * @brief  The assert_param macro is used for function's parameters check.
 * @param  expr: If expr is false, it calls assert_failed function
 *         which reports the name of the source file and the source
 *         line number of the call that failed.
 *         If expr is true, it returns no value.
 * @retval None
 */
#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
/* Exported functions ------------------------------------------------------- */
void assert_failed(uint8_t *file, uint32_t line);
#else
#define assert_param(expr) ((void)0U)
#endif /* USE_FULL_ASSERT */

#ifdef __cplusplus
}
#endif

#endif /* STM32MP1xx_HAL_CONF_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/