-
Notifications
You must be signed in to change notification settings - Fork 5
/
arm-rpi-notes.txt
120 lines (95 loc) · 6.55 KB
/
arm-rpi-notes.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
Circle SDK for Bare Metal Builds
There are a number of configurable system options in the file include/circle/sysconfig.h
For a binary distribution you should do seperate builds for each RPi model
and distribute the files kernel.img, kernel7.img and kernel7l.img.
Optionally you can do a build with RASPPI = 3 to create kernel8-32.img for
an optimized version for the Raspberry Pi 3.
The RASPPI value for each model set in the Makefile:
RASPPI Target Models Optimized for
1 kernel.img A, B, A+, B+, Zero, (CM) ARM1176JZF-S
2 kernel7.img 2, 3, Zero 2, (CM3) Cortex-A7
3 kernel8-32.img 3, Zero 2, (CM3) Cortex-A53
4 kernel7l.img 4B, 400, CM4 Cortex-A72
GCC compiler optimization for ARM-based systems
The gcc compiler can optimize code by taking advantage of CPU specific features.
Especially for ARM CPU's, this can have impact on application performance.
ARM CPU's, even under the same architecture, could be implemented with different
versions of floating point units (FPU). Utilizing full FPU potential improves performance
of heavier operating systems such as full Linux distributions.
-mcpu, -march: Defining the CPU type and architecture
These flags can both be used to set the CPU type. Setting one or the other is sufficient.
GCC supports all Cortex-A processors up to A15 (2010).
Example are 'cortex-a5', 'cortex-a7', 'cortex-a8', 'cortex-a9', 'cortex-a15'.
For specific values on popular boards see table below.
-mfloat-abi, -mfpu: Defining the floating-point application binary interface type (ABI)
and floating point unit type
All ARM Cortex-A processors available today come with a floating-point unit called vector
floating-point VFP. Most also have a SIMD co-processor called NEON.
Confusingly, both are types of floating point units.
VFP is older, IEEE-754 compliant and provides double precision (64bit).
NEON is a multi-function coprocessor that comes with single precision (32bit) vector
functionality in 32bit CPU's, and got double precision in 64bit ARM.
As a result, we have a combination of -mfpu type options, depending on the actual CPU implementation.
Some combinations have an alias: 'neon-vfpv3' is aliased to 'neon' and 'vfpv2' is aliased to 'vfp'.
-mfpu and -mfloat-abi are important flags, because GCC will only use floating-point and NEON
instructions if it is explicitly told to do so. It is also important to set -mfpu in combination
with -mfloat-abi.
-mfloat-abi sets the overall strategy for floating point code compilation.
It has only three values: 'soft', 'softfp', or 'hard'. ‘soft’ generates library calls
for floating-point operations. ‘softfp’ allows the generation of code using hardware
floating-point instructions, but still uses the soft-float calling conventions.
'hard' generates floating-point instructions with FPU-specific calling conventions.
Other options that "can" improve performance in certain circumstances
-mtune This flag can further improve performance by setting the CPU type to a specific CPU model.
For example, on a Raspberry Pi 1, it could be set to -mtune=arm1176jzf-s.
-mneon-for-64bits lets Neon handle scalar 64-bits operations. This flag has no arguments.
It is disabled by default due to high cost of moving data from core registers to Neon on 32bit CPU's.
-funsafe-math-optimizations can improve floating point performance by letting it run through NEON.
Use of NEON instructions may lead to a loss of precision (depending on the version of NEON).
-munaligned-access, -mno-unaligned-access
Enables (or disables) reading and writing of 16- and 32- bit values from addresses that are not
16- or 32- bit aligned. The CPU type defines the correct default, and changing it may
negatively impact performance.
Pre-ARMv6, ARMv6-M, and ARMv8-M default to -mno-unaligned-access.
-munaligned-access is default for all other architectures.
If unaligned access is not enabled, then words in packed data structures are accessed one byte at a time.
Flags that don't need to be specified, because they are correct on default:
-mlittle-endian generates code for little-endian CPUs. This is the default.
CPU information for popular ARM-based boards:
Board CPU Architecture ARM Core FPU
Raspberry Pi 1 Broadcom BCM2835 ARMv6 ARM11 (ARM1176JZFS) VFPv2 (VFP only, no NEON)
Raspberry Pi 2 Broadcom BCM2836 ARMv7-A Cortex-A7 MPcore VFPv4-D32 (VFP and NEON)
BeagleBone Black TI Sitara AM3358/9 ARMv7-A Cortex-A8 VFPv3-D32 (VFP and NEON)
Altera Cyclone V5 5CSEMA4U23C6N A9 ARMv7-A Cortex-A9 MPcore VFPv3-D32 (VFP and NEON)
NanoPi NEO 2 Allwinner H5 ARMv8-A Cortex-A53 VFPv4 (VFP and NEON)
Raspberry Pi 3 Broadcom BCM2837 ARMv8-A Cortex-A53 VFPv4 (VFP and NEON)
Amazon EC2 A1 Graviton ARMv8-A Cortex-A72 VFPv4 (VFP and NEON)
Raspberry Pi 4 Broadcom BCM2711 ARMv8-A Cortex-A72 VFPv4 (VFP and NEON)
GCC compiler options for popular ARM-based boards:
Board GCC optimisation flags
Raspberry Pi 1 -mcpu=arm1176jzf-s -mfloat-abi=hard -mfpu=vfp (alias for vfpv2)
Raspberry Pi 2 -mcpu=cortex-a7 -mfloat-abi=hard -mfpu=neon-vfpv4
BeagleBone Black -mcpu=cortex-a8 -mfloat-abi=hard -mfpu=neon (alias for neon-vfpv3)
Altera Cyclone V5 -mcpu=cortex-a9 -mfloat-abi=hard -mfpu=neon (alias for neon-vfpv3)
Raspberry Pi 3 -mcpu=cortex-a53 -mfloat-abi=hard -mfpu=neon-fp-armv8 -mneon-for-64bits
Amazon EC2 A1 -mcpu=cortex-a72 -mfloat-abi=hard -mfpu=neon-fp-armv8 -mneon-for-64bits
Raspberry Pi 4 -mcpu=cortex-a72 -mfloat-abi=hard -mfpu=neon-fp-armv8 -mneon-for-64bits
GCC compiler tuning options for popular ARM-based boards:
Board GCC extra tuning flags
Raspberry Pi 1 -mtune=arm1176jzf-s
Raspberry Pi 2 -mtune=cortex-a7
BeagleBone Black -mtune=cortex-a8
Altera Cyclone V5 -mtune=cortex-a9
Raspberry Pi 3 -mtune=cortex-a53
Raspberry Pi 4 -mtune=cortex-a72
Note that gcc's code optimisation creates code for a specific CPU/board.
If that code is copied to another platform, it may perform different (e.g. poorly).
How to set compiler options
For most projects, setting the environment variable or adding the flags in the Makefile
variables will do the trick.
export CFLAGS="-mcpu=cortex-a53 -mfloat-abi=hard -mfpu=neon-fp-armv8 -mneon-for-64bits"
Note to crypto miners
Starting with the ARMv8 architecture, a crypto acceleration extension has been added.
On a Raspberry Pi 3 (Cortex A53), it accelerates AES and SHA1/SHA2.
To enable it, use -mcpu=cortex-a53+crypto on a RPi3, and -mcpu=cortex-a72+crypto for RPi4.
Further crypto support (SHA3, SHA512) gets added from ARMv8.4-A onwards.