usb cdc 4g module connection (AEGHB-244) #276
Comments
github-actions
bot
changed the title
|
@mayankbytebeam Which development board do you use? Please make sure the device is powered |
|
@leeebo I used ESP32S3 DevKitC1 and SIM7600 module in this setup. |
|
@mayankbytebeam ESP32S3 DevKitC1 USB Port can not output 5V power. |
|
@leeebo ok now I've powered the modem board exrternally but still some error is coming I've selected the modem baord as |
|
@mayankbytebeam 4G modules generally have multiple interfaces, of which only one is the Modem interface, it seems |
|
@mayankbytebeam If you don't know how to find the endpoint address of the interface, please attach your full log here, i will help |
|
@leeebo sorry for the delay, we have changed the design a bit. Now we are using the N706 modem instead of SIM7600. Serial logs, |
|
@leeebo Can you help to find out the correct cdc endpoint addresses, Here are are serial logs, |
|
@mayankbytebeam From the module's descriptor, which has eight CDC-like interfaces, please first test with the penultimate one (
|
|
Hi, I m facing the same issue. @leeebo which interface class's endpoints should i use from below - sudo lsusb -v -d 2949:7401 Bus 001 Device 008: ID 2949:7401 NEOWAY NEOWAY-N58 -------------------------------------------------------* Above data is from linux using lsusb command with Modem attached to laptop. -----------------------------------------------------*-**- BELOW ESP32 LOG WITH MODEM -----------------------------------------------------*-**- I (10806) modem_board: reconnect after 5s... -----------------------------------------------------*-**- @mayankbytebeam - Any Solution You Found ? |
|
@leeebo Thanks for your input. 0x85 and 0x04 worked for me. |
|
Hi @mayankbytebeam , I guess you are using NEOWAY module. I have tried all the EPs
|
|
@lovepreethitech Hi please link
|
|
Hi @leeebo Could you please share the AT commands list that ESP send to 4G modem. Because my module is unresponsive to some commands. If i get the list i could check if that is working or not. And Yes i have connected the modem reset pin to ESP. |
|
@lovepreethitech Hi, please set the ESP_LOG level to verbose to find the detailed Interaction process |
|
@lovepreethitech Can you try commenting the command that is stucking? Edit : I faced the same issue and after commenting the stuck command it went ahead and connected to my application server. |
|
@mayankbytebeam In which file you comment that ? |
|
@mayankbytebeam I am using SIM7600 4G HAT,i got it form waveshare ,i can connect it to esp32s3,but i found something is wrong. Here are are serial logs: I (10811) modem_board: reconnect after 5s... Core 0 register dump: A2 : 0x3fcb9904 A3 : 0x0000001d A4 : 0x0000000c A5 : 0x00000000 0x400556e5: strlen in ROM Backtrace: 0x4200c1e6:0x3fcba830 0x4200ceb1:0x3fcba870 0x4200cfc1:0x3fcba8a0 0x4200ceb1: esp_dte_handle_line at D:/esp-iot-solution/components/usb/iot_usbh_modem/src/esp_modem_usb_dte.c:79 0x4200cfc1: esp_handle_usb_data at D:/esp-iot-solution/components/usb/iot_usbh_modem/src/esp_modem_usb_dte.c:119 ELF file SHA256: 4830ec08a754ae29 how can i fix it ? |
esp32s3 （合宙 luatos.com） and air780e 4G |
|
Maybe some of the environment dependencies weren't introduced correctly, I've solved my problem and it looks similar to yours
…---Original---
From: ***@***.***>
Date: Tue, Sep 19, 2023 17:58 PM
To: ***@***.***>;
Cc: ***@***.******@***.***>;
Subject: Re: [espressif/esp-iot-solution] usb cdc 4g module connection(AEGHB-244) (Issue #276)
Hello, I used Lexin's esp32s3 DevKitC1 development board and Heju's AIR780E for USB host communication, but there were errors and timeout issues related to the ESP32-S3 modem module. What is the reason for this? I cannot find a solution。Here is my output log
I (43) boot: ESP-IDF v4.4.4-dirty 2nd stage bootloader
I (43) boot: compile time 12:18:19
I (43) boot: chip revision: v0.1
I (45) boot_comm: chip revision: 1, min. bootloader chip revision: 0
I (52) qio_mode: Enabling default flash chip QIO
I (58) boot.esp32s3: Boot SPI Speed : 80MHz
I (63) boot.esp32s3: SPI Mode : QIO
I (67) boot.esp32s3: SPI Flash Size : 8MB
I (72) boot: Enabling RNG early entropy source...
I (77) boot: Partition Table:
I (81) boot: ## Label Usage Type ST Offset Length
I (88) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (96) boot: 1 phy_init RF data 01 01 0000f000 00001000
I (103) boot: 2 factory factory app 00 00 00010000 00100000
I (111) boot: 3 storage Unknown data 01 82 00110000 00100000
I (118) boot: End of partition table
I (123) boot_comm: chip revision: 1, min. application chip revision: 0
I (130) esp_image: segment 0: paddr=00010020 vaddr=3c080020 size=1b664h (112228) map
I (155) esp_image: segment 1: paddr=0002b68c vaddr=3fc99d10 size=0443ch ( 17468) load
I (159) esp_image: segment 2: paddr=0002fad0 vaddr=40374000 size=00548h ( 1352) load
I (161) esp_image: segment 3: paddr=00030020 vaddr=42000020 size=7fbb4h (523188) map
I (249) esp_image: segment 4: paddr=000afbdc vaddr=40374548 size=157bch ( 87996) load
I (274) boot: Loaded app from partition at offset 0x10000
I (275) boot: Disabling RNG early entropy source...
I (286) cpu_start: Pro cpu up.
I (286) cpu_start: Starting app cpu, entry point is 0x403756b0
0x403756b0: call_start_cpu1 at C:/Users/huang/esp/esp-idf/components/esp_system/port/cpu_start.c:148
I (0) cpu_start: App cpu up.
I (300) cpu_start: Pro cpu start user code
I (300) cpu_start: cpu freq: 240000000
I (300) cpu_start: Application information:
I (303) cpu_start: Project name: usb_cdc_4g_module
I (309) cpu_start: App version: 1
I (313) cpu_start: Compile time: Sep 19 2023 17:51:12
I (319) cpu_start: ELF file SHA256: d01d46f315f7c67d...
I (325) cpu_start: ESP-IDF: v4.4.4-dirty
I (331) heap_init: Initializing. RAM available for dynamic allocation:
I (338) heap_init: At 3FCA15A8 len 00048168 (288 KiB): D/IRAM
I (344) heap_init: At 3FCE9710 len 00005724 (21 KiB): STACK/DRAM
I (351) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM
I (357) heap_init: At 600FE000 len 00002000 (8 KiB): RTCRAM
I (364) spi_flash: detected chip: generic
I (368) spi_flash: flash io: qio
I (372) sleep: Configure to isolate all GPIO pins in sleep state
I (379) sleep: Enable automatic switching of GPIO sleep configuration
I (386) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (401) led_indicator: LED Indicator Version: 0.3.0
I (407) gpio: GPIO[15]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (416) led_indicator: blink_lists is null, use default blink list
W (423) led_indicator: ./managed_components/espressif__led_indicator/src/led_indicator.c:280 (_led_indicator_create_com):LED indicator does not have the hal_indicator_set_brightness function
I (440) led_indicator: Indicator create successfully. type:GPIO mode, hardware_data:0xf, is_active_level_high:1, blink_lists:default
I (453) led_indicator: LED Indicator Version: 0.3.0
I (459) gpio: GPIO[17]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (468) led_indicator: blink_lists is null, use default blink list
W (475) led_indicator: ./managed_components/espressif__led_indicator/src/led_indicator.c:280 (_led_indicator_create_com):LED indicator does not have the hal_indicator_set_brightness function
I (492) led_indicator: Indicator create successfully. type:GPIO mode, hardware_data:0x11, is_active_level_high:1, blink_lists:default
I (505) led_indicator: LED Indicator Version: 0.3.0
I (511) gpio: GPIO[16]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (520) led_indicator: blink_lists is null, use default blink list
W (527) led_indicator: ./managed_components/espressif__led_indicator/src/led_indicator.c:280 (_led_indicator_create_com):LED indicator does not have the hal_indicator_set_brightness function
I (544) led_indicator: Indicator create successfully. type:GPIO mode, hardware_data:0x10, is_active_level_high:1, blink_lists:default
I (3576) 4g_main: ====================================
I (3576) 4g_main: ESP 4G Cat.1 Wi-Fi Router
I (3576) 4g_main: ====================================
I (3582) modem_board: iot_usbh_modem, version: 0.1.6
I (3587) modem_board: Force reset modem board....
I (3593) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (3602) modem_board: Resetting modem using io=13, level=0
I (3808) modem_board: Waiting for modem initialize ready
I (8808) USB_HCDC: iot_usbh_cdc, version: 0.1.3
I (8808) IOT_USBH: iot_usbh, version: 0.1.2
I (8838) IOT_USBH: USB Port=1 init succeed, fifo strategy=0
I (8838) USB_HCDC: CDC task start
I (8838) IOT_USBH: usb port start succeed
I (8842) USB_HCDC: usbh cdc driver install succeed
I (8847) USB_HCDC: Waiting CDC Device Connection
I (8852) IOT_USBH: USB Processing Start
I (8857) IOT_USBH: Waiting USB Connection
I (8861) IOT_USBH: Port power: ON Succeed
I (9116) IOT_USBH: line 131 PORT_EVENT_CONNECTION
I (9216) IOT_USBH: Resetting Port
I (9276) IOT_USBH: Port reset succeed
I (9276) IOT_USBH: Getting Port Speed
I (9276) IOT_USBH: USB Speed: full-speed
I (9278) IOT_USBH: Pipe init succeed, addr: 00
I (9283) IOT_USBH: Set Device Addr = 1
I (9288) IOT_USBH: Set Device Addr Done
I (9292) IOT_USBH: get device desc
I (9297) IOT_USBH: get device desc, actual_num_bytes:26
*** Device descriptor ***
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0xef
bDeviceSubClass 0x2
bDeviceProtocol 0x1
bMaxPacketSize0 64
idVendor 0x19d1
idProduct 0x1
bcdDevice 2.00
iManufacturer 1
iProduct 2
iSerialNumber 3
bNumConfigurations 1
I (9326) IOT_USBH: get short config desc
I (9331) IOT_USBH: get config desc, actual_num_bytes:16
I (9336) IOT_USBH: get full config desc
I (9341) IOT_USBH: get full config desc, actual_num_bytes:281
*** Configuration descriptor ***
bLength 9
bDescriptorType 2
wTotalLength 273
bNumInterfaces 8
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
bMaxPower 200mA
*** Interface descriptor ***
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 0xe0
bInterfaceSubClass 0x1
bInterfaceProtocol 0x3
iInterface 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 0x3 INT
wMaxPacketSize 8
bInterval 4
*** Interface descriptor ***
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 0xa
bInterfaceSubClass 0x0
bInterfaceProtocol 0x0
iInterface 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x1 EP 1 OUT
bmAttributes 0x2 BULK
wMaxPacketSize 64
bInterval 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 0x2 BULK
wMaxPacketSize 64
bInterval 0
*** Interface descriptor ***
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 0x2
bInterfaceSubClass 0x2
bInterfaceProtocol 0x1
iInterface 7
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 0x3 INT
wMaxPacketSize 16
bInterval 255
*** Interface descriptor ***
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 0xa
bInterfaceSubClass 0x0
bInterfaceProtocol 0x0
iInterface 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x2 EP 2 OUT
bmAttributes 0x2 BULK
wMaxPacketSize 64
bInterval 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 0x2 BULK
wMaxPacketSize 64
bInterval 0
*** Interface descriptor ***
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 0x2
bInterfaceSubClass 0x2
bInterfaceProtocol 0x1
iInterface 8
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 0x3 INT
wMaxPacketSize 16
bInterval 255
*** Interface descriptor ***
bLength 9
bDescriptorType 4
bInterfaceNumber 5
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 0xa
bInterfaceSubClass 0x0
bInterfaceProtocol 0x0
iInterface 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x3 EP 3 OUT
bmAttributes 0x2 BULK
wMaxPacketSize 64
bInterval 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 0x2 BULK
wMaxPacketSize 64
bInterval 0
*** Interface descriptor ***
bLength 9
bDescriptorType 4
bInterfaceNumber 6
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 0x2
bInterfaceSubClass 0x2
bInterfaceProtocol 0x1
iInterface 9
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 0x3 INT
wMaxPacketSize 16
bInterval 255
*** Interface descriptor ***
bLength 9
bDescriptorType 4
bInterfaceNumber 7
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 0xa
bInterfaceSubClass 0x0
bInterfaceProtocol 0x0
iInterface 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x4 EP 4 OUT
bmAttributes 0x2 BULK
wMaxPacketSize 64
bInterval 0
*** Endpoint descriptor ***
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 0x2 BULK
wMaxPacketSize 64
bInterval 0
I (9675) IOT_USBH: Set Device Configuration = 1
I (9680) IOT_USBH: Set Device Configuration Done
I (9685) IOT_USBH: Pipe init succeed, addr: 87
I (9690) IOT_USBH: Pipe init succeed, addr: 02
I (9695) USB_HCDC: CDC Device Connected
I (9700) esp-modem: --------- Modem PreDefined Info ------------------
I (9707) esp-modem: Model: User Defined
I (9712) esp-modem: Modem itf: IN Addr:0x87, OUT Addr:0x02
I (9718) esp-modem: ----------------------------------------------------
I (9725) gpio: GPIO[12]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (9735) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (9745) USB_HCDC: rx0 flush -0 = 0
I (9748) 4g_main: Modem Board Event: USB connected
I (9748) modem_board: DTE reconnect, reconnecting ...
I (10759) modem_board: reconnect after 5s...
I (11759) modem_board: reconnect after 4s...
I (12759) modem_board: reconnect after 3s...
I (13759) modem_board: reconnect after 2s...
I (14759) modem_board: reconnect after 1s...
I (14759) modem_board: Modem state STAGE_SYNC, Start
E (16769) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
I (16784) modem_board: Current timeouts: 1 and errors: 0
E (46784) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
W (46784) esp_modem_dce: esp_modem_dce_generic_command(22): Command:+++ response timeout
E (48789) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
E (50794) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
I (50809) modem_board: Current timeouts: 2 and errors: 0
W (50809) modem_board: Reset modem through reset pin........
W (50811) 4g_main: Modem Board Event: Hardware restart
I (50812) modem_board: modem_board_reset!
I (56022) 4g_main: Modem Board Event: Hardware restart done
E (58022) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
I (58037) modem_board: Current timeouts: 3 and errors: 0
I (58037) modem_board: modem_board_power_down!
E (68538) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
E (70543) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
I (70558) modem_board: Current timeouts: 4 and errors: 0
I (70558) modem_board: modem_board_power_down!
E (81059) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
E (83064) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
I (83079) modem_board: Current timeouts: 5 and errors: 0
I (83079) modem_board: modem_board_power_down!
E (93580) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
E (95585) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
E (95590) modem_board: modem_board_start_up(225): sending sync failed
I (95597) modem_board: Modem state STAGE_SYNC, Start
E (97613) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutem_dce: esp_modem_dce_generic_command(22): Command:AT
I (97628) modem_board: Current timeouts: 1 and errors: 0
E (127628) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
W (127628) esp_modem_dce: esp_modem_dce_generic_command(22): Command:+++ response timeout
E (129633) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutdem_dce: esp_modem_dce_generic_command(22): Command:AT
E (131638) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutdem_dce: esp_modem_dce_generic_command(22): Command:AT
I (131653) modem_board: Current timeouts: 2 and errors: 0
W (131653) modem_board: Reset modem through reset pin........
W (131656) 4g_main: Modem Board Event: Hardware restart
I (131656) modem_board: modem_board_reset!
I (136866) 4g_main: Modem Board Event: Hardware restart done
E (138866) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutdem_dce: esp_modem_dce_generic_command(22): Command:AT
I (138881) modem_board: Current timeouts: 3 and errors: 0
I (138881) modem_board: modem_board_power_down!
E (149383) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutdem_dce: esp_modem_dce_generic_command(22): Command:AT
E (151388) esp-modem-dte: esp_modem_dte_send_cmd(266): process command timeout
response timeoutdem_dce: esp_modem_dce_generic_command(22): Command:AT
I (151403) modem_board: Current timeouts: 4 and errors: 0
I (151403) modem_board: modem_board_power_down!
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you commented.Message ID: ***@***.***>
|
|
@Y1hsiaochunnn I can use the code from the Gitee library normally and have added the AIR780E option, which is convenient for me to apply to projects。https://gitee.com/dog_who_loves_cat_mint/esp32_-cdc_4-g |
It's a known bug, log in #295. will fix soon |
How to set up SIM7600 modem via ESP32S3 USB Port.
IDF Version: 5.0.0
ESP IoT Solution Version: Master Branch
Just selected
user definedmodem board in the component config -> usb host modm.Serial Logs:
Ya that sit, it is hanged there. I guess it is wating for usb device.
Any help will be appreciated :)
The text was updated successfully, but these errors were encountered: