diff --git a/SheetMetalCmd.py b/SheetMetalCmd.py
index 0d6b55f..bdb0dbc 100644
--- a/SheetMetalCmd.py
+++ b/SheetMetalCmd.py
@@ -176,6 +176,75 @@ def smMakeReliefFace(edge, dir, gap, reliefW, reliefD, reliefType, op=""):
     return face
 
 
+def smMakePerforationFace(
+        edge,
+        dir,
+        bendR,
+        bendA,
+        perforationAngle,
+        flipped,
+        extLen,
+        gap1,
+        gap2,
+        lenIPerf1,
+        lenIPerf2,
+        lenPerf,
+        lenNPerf,
+        op="",
+):
+    L0 = (edge.LastParameter - gap2 - lenIPerf2) - (edge.FirstParameter + gap1 + lenIPerf1)
+    Lp = lenPerf
+    Ln = lenNPerf
+    P0 = (L0-Ln) / (Lp+Ln)
+    P = math.ceil(P0)
+    N = P+1
+    F = L0 / (math.ceil(P0)*Lp + math.ceil(P0)*Ln + Ln)
+
+    if perforationAngle == 0:
+        perforationAngle = bendA
+    extAngle = (perforationAngle - bendA) / 2;
+    S = (1 / math.cos(extAngle * (2*math.pi/360)))
+
+    pivotL = -bendR
+    swingL = extLen + (S-1)*(bendR+extLen)
+    if not flipped:
+        pivotL = extLen - pivotL
+        swingL = extLen - swingL
+
+    # Initial perf, near
+    p1 = edge.valueAt(edge.FirstParameter + gap1) + dir.normalize() * pivotL
+    p2 = edge.valueAt(edge.FirstParameter + gap1 + lenIPerf1) + dir.normalize() * pivotL
+    p3 = edge.valueAt(edge.FirstParameter + gap1 + lenIPerf1) + dir.normalize() * swingL
+    p4 = edge.valueAt(edge.FirstParameter + gap1) + dir.normalize() * swingL
+    w = Part.makePolygon([p1, p2, p3, p4, p1])
+    face = Part.Face(w)
+    totalFace = face
+
+    # Initial perf, far
+    p1 = edge.valueAt(edge.LastParameter - gap2 - lenIPerf2) + dir.normalize() * pivotL
+    p2 = edge.valueAt(edge.LastParameter - gap2) + dir.normalize() * pivotL
+    p3 = edge.valueAt(edge.LastParameter - gap2) + dir.normalize() * swingL
+    p4 = edge.valueAt(edge.LastParameter - gap2 - lenIPerf2) + dir.normalize() * swingL
+    w = Part.makePolygon([p1, p2, p3, p4, p1])
+    face = Part.Face(w)
+    totalFace = totalFace.fuse(face)
+
+    # Perforations, inner
+    for i in range(P):
+        x = (edge.FirstParameter + gap1 + lenIPerf1) + (Ln * F * (i+1)) + (Lp * F * i)
+        p1 = edge.valueAt(x) + dir.normalize() * pivotL
+        p2 = edge.valueAt(x + Lp*F) + dir.normalize() * pivotL
+        p3 = edge.valueAt(x + Lp*F) + dir.normalize() * swingL
+        p4 = edge.valueAt(x) + dir.normalize() * swingL
+        w = Part.makePolygon([p1, p2, p3, p4, p1])
+        face = Part.Face(w)
+        totalFace = totalFace.fuse(face)
+
+    if hasattr(totalFace, "mapShapes"):
+        totalFace.mapShapes([(edge, totalFace)], None, op)
+    return totalFace
+
+
 def smMakeFace(edge, dir, extLen, gap1=0.0, gap2=0.0, angle1=0.0, angle2=0.0, op=""):
     len1 = extLen * math.tan(math.radians(angle1))
     len2 = extLen * math.tan(math.radians(angle2))
@@ -917,6 +986,11 @@ def smBend(
     sketch=None,
     extendType="Simple",
     LengthSpec="Leg",
+    Perforate=False,
+    PerforationAngle=0.0,
+    PerforationInitialLength=5.0,
+    PerforationMaxLength=5.0,
+    NonperforationMaxLength=5.0,
 ):
     # if sketch is as wall
     sketches = False
@@ -1287,8 +1361,8 @@ def smBend(
             # Part.show(wallSolid.Faces[2])
             thk_faceList.append(wallSolid.Faces[2])
 
-        # Produce bend Solid
         if not (unfold):
+            # Produce bend Solid
             if bendA > 0.0:
                 # create bend
                 # narrow the wall if we have gaps
@@ -1302,6 +1376,41 @@ def smBend(
                 resultSolid = resultSolid.fuse(wallSolid)
                 # Part.show(resultSolid,"resultSolid")
 
+            # Remove perforation
+            if Perforate:
+                #CHECK I'm not sure about flipped - the main one gets overwritten for each sublist item
+                perfFace = smMakePerforationFace(
+                    lenEdge,
+                    thkDir,
+                    bendR,
+                    bendA,
+                    PerforationAngle,
+                    flipped,
+                    thk,
+                    gap1,
+                    gap2,
+                    PerforationInitialLength,
+                    PerforationInitialLength,
+                    PerforationMaxLength,
+                    NonperforationMaxLength,
+                    op="SMR",
+                )
+                # Part.show(perfFace)
+                #CHECK 'Part.Compound' object has no attribute 'normalAt' ; might need it
+                # if perfFace.normalAt(0, 0) != FaceDir:
+                #     perfFace.reverse()
+                if PerforationAngle > 0.0:
+                    perfFace = perfFace.rotate(
+                        revAxisP,
+                        revAxisV,
+                        (bendA/2)-(PerforationAngle/2)
+                    )
+                    perfSolid = perfFace.revolve(revAxisP, revAxisV, PerforationAngle)
+                else:
+                    perfSolid = perfFace.revolve(revAxisP, revAxisV, bendA)
+                # Part.show(perfSolid)
+                resultSolid = resultSolid.cut(perfSolid)
+
         # Produce unfold Solid
         else:
             if bendA > 0.0:
@@ -1316,10 +1425,42 @@ def smBend(
                 resultSolid = resultSolid.fuse(unfoldSolid)
 
             if extLen > 0.0:
+                # Flatten the wall back out
                 wallSolid.rotate(revAxisP, revAxisV, -bendA)
                 # Part.show(wallSolid, "wallSolid")
                 wallSolid.translate(FaceDir * unfoldLength)
                 resultSolid = resultSolid.fuse(wallSolid)
+
+            # Remove perforation
+            if Perforate:
+                perfFace = smMakePerforationFace(
+                    lenEdge,
+                    thkDir,
+                    bendR,
+                    bendA,
+                    PerforationAngle,
+                    flipped,
+                    thk,
+                    gap1,
+                    gap2,
+                    PerforationInitialLength,
+                    PerforationInitialLength,
+                    PerforationMaxLength,
+                    NonperforationMaxLength,
+                    op="SMR",
+                )
+                #CHECK 'Part.Compound' object has no attribute 'normalAt' ; might need it
+                # if perfFace.normalAt(0, 0) != FaceDir:
+                #     perfFace.reverse()
+                if PerforationAngle > 0.0:
+                    perfUnfoldLength = (bendR + kfactor * thk) * PerforationAngle * math.pi / 180.0
+                    perfFace = perfFace.translate(FaceDir * ((unfoldLength/2)-(perfUnfoldLength/2)))
+                    perfSolid = perfFace.extrude(FaceDir * perfUnfoldLength)
+                else:
+                    perfSolid = perfFace.extrude(FaceDir * unfoldLength)
+                # Part.show(perfSolid)
+                resultSolid = resultSolid.cut(perfSolid)
+            
     # Part.show(resultSolid, "resultSolid")
     return resultSolid, thk_faceList
 
@@ -1530,6 +1671,41 @@ def _addProperties(self, obj):
             None,
             "ParametersEx3",
         )
+        smAddBoolProperty(
+            obj,
+            "Perforate",
+            FreeCAD.Qt.translate("App::Property", "Enable Perforation"),
+            False,
+            "ParametersPerforation",
+        )
+        smAddAngleProperty(
+            obj,
+            "PerforationAngle",
+            FreeCAD.Qt.translate("App::Property", "Perforation Angle"),
+            0.0,
+            "ParametersPerforation",
+        )
+        smAddLengthProperty(
+            obj,
+            "PerforationInitialLength",
+            FreeCAD.Qt.translate("App::Property", "Initial Perforation Length"),
+            5.0,
+            "ParametersPerforation",
+        )
+        smAddLengthProperty(
+            obj,
+            "PerforationMaxLength",
+            FreeCAD.Qt.translate("App::Property", "Perforation Max Length"),
+            5.0,
+            "ParametersPerforation",
+        )
+        smAddLengthProperty(
+            obj,
+            "NonperforationMaxLength",
+            FreeCAD.Qt.translate("App::Property", "Non-Perforation Max Length"),
+            5.0,
+            "ParametersPerforation",
+        )
 
     def getElementMapVersion(self, _fp, ver, _prop, restored):
         if not restored:
@@ -1613,6 +1789,11 @@ def execute(self, fp):
                 mingap=fp.minGap.Value,
                 maxExtendGap=fp.maxExtendDist.Value,
                 LengthSpec=fp.LengthSpec,
+                Perforate=fp.Perforate,
+                PerforationAngle=fp.PerforationAngle.Value,
+                PerforationInitialLength=fp.PerforationInitialLength.Value,
+                PerforationMaxLength=fp.PerforationMaxLength.Value,
+                NonperforationMaxLength=fp.NonperforationMaxLength.Value,
             )
             faces = smGetFace(f, s)
             face = faces