MatrixClock

This is an NTP clock built on an ESP8266 & five MAX7219 or MAX7221 connected in series.

• automatic synchronization with NTP servers or manually with browser time
• automatic Daylight Saving Time
• three fonts to choose from
• show weather from OpenWeatherMap (for 5 seconds, every 10 seconds)
• control the brightness of the display by sunrise/sunset or from 8am to 8pm if there is no OpenWeatherMap account
• web interface Bootstrap + jQuery
• updating the firmware and file system image via the web interface
• DFPlayer Mini as daily alarm and hourly chime
• individual volume for daily alarm and hourly chime
• hourly chime with a choice of 10 tracks and an interval setting
• daily alarm clock with a choice of 10 tracks and a smooth increase in volume
• bonus, a simple mp3 player with saving the current track number in RTC memory
• bonus, OpenWeatherMap recorder (logger) with charts

The software is provided "AS IS" without warranty of any kind

• Download Flash Download Tools from here
• Download MatrixClock *.bin files
• In Flash Download Tools:
  • set SPI speed 80MHz
  • set SPI Mode QIO
  • set Flash Size 32Mbit
  • check DoNotChgBin
  • fw_latest.bin at address 0x00000
  • fs_latest.bin at address 0x200000
• Connect any ESP8266 with QIO 4MB flash to USB, select COM port & baud rate than press Start

• Connect five MAX7219 or MAX7221 as follows:
  • GPIO13/D7 to DIN/MOSI
  • GPIO14/D5 to CLK/SCLK
  • GPIO15/D8 to CS (can be changed via the WEB interface after)
  • Vcc to +4.0v..+5.0v
  • Gnd to Gnd
  • recommend changing the resistor R1 from 10K to 59K (for 2.5V/10mA LEDs) or to 25K (for 2.5V/20mA LEDs)
• Connect DFPlayer Mini (YX5200, YX5300, JL AAxxxx or GD3200B) as follows:
  • GPIO5/D1 to RX
  • GPIO4/D2 to TX
  • Vcc to +3.2v..+5.0v
  • Gnd to Gnd
  • 2W/4ohm speaker to SPK1 and SPK2
  • put files from mp3_sd_root folder to SD card, up to 36GB formatted as FAT16 or FAT32
  • if you hear loud noise, add a 1K resistor between GPIO4/D2 and TX pins
  • recommended to set the jumper to the STBY-> BUSY position
• Voltage
  • to show the correct voltage, change the resistor R1 on the WeMos D1 Mini from 220K to 470K, then connect pin A0 to pin 3V3

• Connect to MatrixClock WiFi access point using password 12345678
• Type in browser http://192.168.4.1/
• Put User Name: admin and Password: 12345678
• For security purposes, please change login/password for the access point Settings -> Access Point Config and Settings -> Server Config page then click Save
• If MatrixClock screen doesn't blink 5 times and doesn't show time go to Matrix Driver Config page and rearrange CS pin according to your schematic then click Save and Reboot. Make sure GPIO13/D7 connected to DIN/MOSI and GPIO14/D5 to CLK/SCLK
• Set WiFi Network name and password in Settings -> Station Config page than click Save and Reboot
• The MatrixClock will connect to the WiFi network and MatrixClock access point will disappear
• Type in browser http://matrixclock.local/ (use IP address instead of mDNS on Android and Win7 devices, address can be found in the UART logs at speed 115200bps)
• Go to Time or Settings -> NTP Config and set your timezone than click Save and Reboot
• Get free API key from OpenWeatherMap and put it in corresponding field on Settings -> Weather Config page, set other filds than click Save and Reboot. Matrix Clock now updates the current weather every 2.5 minutes and shows the weather icon and temperature for 5 seconds every 10 seconds.

Used library:

• DFPlayer