Skip to content

hiter123/unitree_ros

 
 

Repository files navigation

Introduction

Here are the ROS packages of Unitree robots, namely Laikago, Aliengo and A1. You can load robots and joint controllers in Gazebo, so you can do low-level control(control the torque, position and angular velocity) on the robot joints. Please watch out that the Gazebo simulation cannot do high-level control, namely walking. Besides of these simulation functions, you can also control your real robots in ROS by the unitree_legged_real. For real robots, you can do high-level and low-level control by our ROS packages.

Packages:

Robot description: a1_description, aliengo_description, laikago_description

Robot and joints controller: unitree_controller

Basic function: unitree_legged_msgs

Simulation related: unitree_gazebo, unitree_legged_control

Real robot control related: unitree_legged_real

Dependencies

  • ROS melodic or ROS kinetic(has not been tested)
  • Gazebo8
  • unitree_legged_sdk: If your robot is suitable for unitree_legged_sdk, then you do not need aliengo_sdk.
  • aliengo_sdk: If your robot is suitable for aliengo_sdk, then you do not need unitree_legged_sdk.

Configuration

Make sure the following exist in your ~/.bashrc file or export them in terminal. melodic, gazebo-8, ~/catkin_ws, amd64 and the paths to unitree_legged_sdk should be replaced in your own case. If your use unitree_legged_sdk, then you need to set UNITREE_SDK_VERSION=3_2 and the path UNITREE_LEGGED_SDK_PATH. Otherwise, if you use aliengo_sdk, you need to set UNITREE_SDK_VERSION=3_1 and the path ALIENGO_SDK_PATH.

source /opt/ros/melodic/setup.bash
source /usr/share/gazebo-8/setup.sh
source ~/catkin_ws/devel/setup.bash
export ROS_PACKAGE_PATH=~/catkin_ws:${ROS_PACKAGE_PATH}
export GAZEBO_PLUGIN_PATH=~/catkin_ws/devel/lib:${GAZEBO_PLUGIN_PATH}
export LD_LIBRARY_PATH=~/catkin_ws/devel/lib:${LD_LIBRARY_PATH}
# 3_1, 3_2
export UNITREE_SDK_VERSION=3_2
export UNITREE_LEGGED_SDK_PATH=~/unitree_legged_sdk
export ALIENGO_SDK_PATH=~/aliengo_sdk
# amd64, arm32, arm64
export UNITREE_PLATFORM="amd64"

Build

If you just need to send message from the ROS on robot's NX or TX2, you can just copy unitree_legged_msgs and unitree_legged_real to catkin_ws/src folder and run catkin_make to compile.

If you would like to fully compile the unitree_ros, please run the following command to install relative packages.

If your ROS is melodic:

sudo apt-get install ros-melodic-controller-interface  ros-melodic-gazebo-ros-control ros-melodic-joint-state-controller ros-melodic-effort-controllers ros-melodic-joint-trajectory-controller

Else if your ROS is kinetic:

sudo apt-get install ros-kinetic-controller-manager ros-kinetic-ros-control ros-kinetic-ros-controllers ros-kinetic-joint-state-controller ros-kinetic-effort-controllers ros-kinetic-velocity-controllers ros-kinetic-position-controllers ros-kinetic-robot-controllers ros-kinetic-robot-state-publisher ros-kinetic-gazebo8-ros ros-kinetic-gazebo8-ros-control ros-kinetic-gazebo8-ros-pkgs ros-kinetic-gazebo8-ros-dev

And open the file unitree_gazebo/worlds/stairs.world. At the end of the file:

<include>
    <uri>model:///home/unitree/catkin_ws/src/unitree_ros/unitree_gazebo/worlds/building_editor_models/stairs</uri>
</include>

Please change the path of building_editor_models/stairs to the real path on your PC.

Then you can use catkin_make to build:

cd ~/catkin_ws
catkin_make

If you face a dependency problem, you can just run catkin_make again.

Detail of Packages

unitree_legged_control:

It contains the joints controllers for Gazebo simulation, which allows user to control joints with position, velocity and torque.

unitree_legged_msgs:

ros-type message, including command and state of high-level and low-level control. It would be better if it be compiled firstly, otherwise you may have dependency problems (such as that you can't find the header file).

The description of robots:

Namely the description of A1, Aliengo and Laikago. Each package include mesh, urdf and xacro files of robot. Take Laikago as an example, you can check the model in Rviz by:

roslaunch laikago_description laikago_rviz.launch

unitree_gazebo & unitree_controller:

You can launch the Gazebo simulation by the following command:

roslaunch unitree_gazebo normal.launch rname:=a1 wname:=stairs

Where the rname means robot name, which can be laikago, aliengo or a1. The wname means world name, which can be earth, space or stairs. And the default value of rname is laikago, while the default value of wname is earth. In Gazebo, the robot should be lying on the ground with joints not activated.

Stand controller

After launching the gazebo simulation, you can start to control the robot:

rosrun unitree_controller unitree_servo

And you can add external disturbances, like a push or a kick:

rosrun unitree_controller unitree_external_force

Position and pose publisher

Here we showed how to control the position and pose of robot without a controller, which should be useful in SLAM or visual development.

Then run the position and pose publisher in another terminal:

rosrun unitree_controller unitree_move_kinetic

The robot will turn around the origin, which is the movement under the world coordinate. And inside of the source file move_publisher, we also offered the method to move robot under robot coordinate. You can change the value of def_frame to coord::ROBOT and run the catkin_make again, then the unitree_move_publisher will move robot under its own coordinate.

unitree_legged_real

Setup the net connection

First, please connect the network cable between your PC and robot. Then run ifconfig in a terminal, you will find your port name. For example, enx000ec6612921.

Then, open the ipconfig.sh file under the folder unitree_legged_real, modify the port name to your own. And run the following commands:

sudo chmod +x ipconfig.sh
sudo ./ipconfig.sh

If you run the ifconfig again, you will find that port has inet and netmask now. In order to set your port automatically, you can modify interfaces:

sudo gedit /etc/network/interfaces

And add the following 4 lines at the end:

auto enx000ec6612921
iface enx000ec6612921 inet static
address 192.168.123.162
netmask 255.255.255.0

Where the port name have to change to your own.

Run the package

You can control your real robot(only A1 and Aliengo) from ROS by this package.

First you have to run the real_launch under root account:

sudo su
source /home/yourUserName/catkin_ws/devel/setup.bash
roslaunch unitree_legged_real real.launch rname:=a1 ctrl_level:=highlevel firmwork:=3_2

Please watchout that the /home/yourUserName means the home directory of yourself. These commands will launch a LCM server. The rname means robot name, which can be a1 or aliengo(case does not matter), and the default value is a1. And the ctrl_level means the control level, which can be lowlevel or highlevel(case does not matter), and the default value is highlevel. Under the low level, you can control the joints directly. And under the high level, you can control the robot to move or change its pose. The firmwork means the firmwork version of the robot. The default value is 3_2 Now all the A1's firmwork version is 3_2, and most Aliengo's firmwork version is 3_1.(will update in the future)

To do so, you need to run the controller in another terminal(also under root account):

rosrun unitree_legged_real position_lcm

We offered some examples. When you run the low level controller, please make sure the robot is hanging up. The low level contains:

position_lcm
velocity_lcm
torque_lcm

The velocity_lcm and torque_lcm have to run under root account too. Please use the same method as runing real_launch.

And when you run the high level controller, please make sure the robot is standing on the ground. The high level only has walk_lcm.

About

No description, website, or topics provided.

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • C++ 75.1%
  • C 14.9%
  • CMake 9.7%
  • Shell 0.3%